FIRST TIME OPERATING INSTRUCTIONS
FIRST TIME OPERATING INSTRUCTIONS WARNING Always keep hands clear of winch rope, hook loop, hook and fairlead opening during installation, operation, and when spooling in or out. 3. Grasp hook strap and spool out the winch rope to the last 5 wraps on the drum (10 wraps if synthetic rope).
SPOOLING IN UNDER LOAD WARNING Never exceed winch or winch rope rated capacity. Power-in the winch rope evenly and tightly on the drum. This prevents the outer winch wraps from sinking into the inner wraps, binding, and damaging the winch rope. Avoid shock loads when spooling, by pulsing the control switch to take up winch rope slack. Shock loads can momentarily far exceed the winch and rope ratings. SPOOLING IN UNDER NO LOAD WARNING Never touch winch rope or hook while someone else is at the control switch, when winch rope is under load or during winching operation. Spooling with an Assistant : Have the assistant hold the hook strap putting as much constant tension on the winch rope as possible. While keeping tension, the assistant should walk toward the winch while you operate the control switch spooling in the winch rope. Release the switch when the hook is a minimum of 6 ft. (2m) from the fairlead opening. Spool in the remainder for storage as directed below. Spooling Alone : Arrange the winch rope to be spooled so it will not kink or tangle when spooled. Be sure any winch rope on the drum is tightly and evenly layered. Spool enough winch rope to complete the next full layer on the drum. Tighten and straighten the layer. Repeat process until the hook is a minimum of 6 ft. (2 m) from the fairlead opening. SPOOLING REMAINDER FOR STORAGE When the hook is within 6 ft. (2 m) of the fairlead, disconnect the hook from the anchor or load. Hold onto the supplied hook strap and hold tension on the winch rope. Slowly power-in the winch by “pulsing” the power-in switch on the remote control until the hook is within 3 ft. (1 m) of the fairlead. Stop winching in and attach the hook to a suitable anchor point on the vehicle.
WARNING Never touch winch rope or hook while someone else is at the control switch, when winch rope is under load or during winching operation. WARNING Never let winch rope slip through your hands. 11. With gloves on, hold tension on the winch rope with one hand; carefully push the winch rope to the side of the drum the winch rope is attached to so there are no gaps between each coil on the drum. 12. The following steps should be done using two people for proper safety. If you attempt to tension your winch rope alone be sure to always set the parking brake, place the transmission in gear or park and turn the vehicle off every time you exit the vehicle to inspect the winch rope. NOTICE Use care to evenly wrap each layer to prevent damage to the rope. WARNING Never use remote when vehicle is not in line of sight of operator. 13. The driver of the vehicle should operate the winch. 14. Instruct your assistant to stand to the side of the vehicle and away from the winch rope. NOTE: Your assistant should signal you if the winch rope is winding correctly or incorrectly by watching it move across the fairlead as the winch rope is powered in. 15. Start the vehicle and place the transmission in neutral. Then release the parking brake while applying moderate brake pedal pressure. 16. Power-in the winch rope to start winching in. 17. After winching in for approximately 6 ft. (2m), stop winching. 18. Slowly let up off of the brake pedal and then apply the parking brake. This will ensure that there is no load on the winch rope. 19. Place the transmission in park or in gear and turn the vehicle off. 20 Exit the vehicle and inspect the winch to make sure that the winch rope is being evenly wound onto the winch drum and not sinking into the lower layer. If the winch rope is sinking, power-out the winch rope by pushing the power-out button on the remote control and repeat this step from the beginning with more brake pedal pressure.
NOTICE Do not power the hook into the fairlead. This could cause damage to the fairlead. Once the hook is suitably attached to the vehicle, power-in the remaining slack in the winch rope by “pulsing” the power-in switch on the remote control until there is minimal slack in the winch rope. OVERLOADING/OVERHEATING WARNING Always be aware of possible hot surfaces at winch motor, drum or rope during or after winch use. This winch is rated for intermittent duty. When the motor approaches stall speed, very rapid heat buildup occurs which may cause motor damage. Double-line rigging (see The Basic Guide to Winching Techniques) will reduce the amperage draw, and reduce heat buildup in the motor. This allows longer continual use. STRETCHING WINCH ROPE WARNING Always prestretch rope and respool under load before use. WARNING Always inspect winch rope, hook, and slings before operating winch. Frayed, kinked or damaged winch rope must be replaced immediately. Damaged components must be replaced before operation. Protect parts from damage. Stretching (tensioning) the winch rope is critical to ensure a long product life. Tensioning the winch rope will prevent outer layers of winch rope from pinching and deforming the inner layers. During its first use, a new winch rope must be spooled onto its drum under a load of at least 1000 lbs. (454 kgs). Use the following instructions to properly stretch the winch rope onto the winch drum. WARNING Always wear heavy gloves when handling winch rope. 1. Choose a FLAT AND LEVEL location that is large enough to run out almost the entire length of winch rope. 2. Disengage clutch.
4. Be sure to check that the winch rope is winding off of the bottom of the drum or the automatic load holding brake will not function properly. NOTE: If the winch rope is winding off the top of the drum, you have powered the winch “out” instead of “in”. Be sure you are powering in. WARNING Always wind the winch rope on bottom (mountside) of drum. NOTICE For proper function of the winch brake, the winch rope must be spooled onto the drum in the specified direction. *See drum rotation label located on winch. 5. Once the winch rope is spooled out, engage clutch. WARNING Always ensure hook latch is closed. WARNING Always apply load only to the center of hook. WARNING Never apply load to hook tip or use hook that is bent or twisted. 6. Attach the hook end of the rope to a suitable anchor point. WARNING Always remove any obstacle that may interfere with safe operation of the winch. WARNING Never wrap winch rope back onto itself. Use a chain or strap on the anchor. WARNING Always be certain the anchor you select will withstand the load and the strap or chain will not slip. 7. Return to your vehicle. 8. Back the vehicle away from the anchor point until there is very little slack in the winch rope. 9. Set the parking brake, place the vehicle in gear or park and turn the vehicle off. WARNING Always stand clear of winch rope and load and keep others away while winching. 10. Exit vehicle. WARNING! Never exit the vehicle with a load on the winch rope. While standing approximately 8 ft. (2.44 m) away from the winch, power-in the winch until all of the slack is wound onto the winch drum.
WARN INDUSTRIES 13
WARN INDUSTRIES 14
Powered by FlippingBook