EVO Winch Service Manual
GENERAL SAFETY PRECAUTIONS
Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided installation and operating instructions and other information on labels and in this guide. This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judgment. CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT. This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury or death. WARNING and CAUTION are signal words that identify the level of hazard. These signal words mean: WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations. CAUTION signals a hazard that may cause minor to moderate injury, if you do not follow recommendations. This guide uses NOTICE to call attention to important mechanical information and NOTE to emphasize general information worthy of special attention.
WARN I NG
CAUT I ON
IMPACT AND MOVING PARTS ENTANGLEMENT HAZARD Failure to observe these instructions could lead to severe injury or death • Always take time to fully read the Instructions and/or Operations Guide, and/or Basic Guide to Winching Techniques, in order to understand your winch and its operations. • Always use extreme caution when drilling on any vehicle. Make sure that all fuel lines, brake lines, electrical wires, and other objects are not punctured or damaged when/if drilling on the vehicle. Thoroughly inspect the area to be drilled (on both sides of material) prior to drilling, and relocate any objects that may be damaged. Failure to inspect the area to be drilled may result in vehicle damage, electrical shock, fire or personal injury. • Always wear safety glasses when installing this kit. A drilling operation will cause flying metal chips. Flying chips can cause eye injury.
MOVING PARTS ENTANGLEMENT HAZARD Failure to observe these instructions could lead to minor or moderate injury
• Always use proper tools when making repairs. • Always utilize a qualified WARN service technician when specialized tools are required. • Always disconnect all wires from the positive battery terminal or disconnect hydraulic hoses from the winch motor before beginning any work on the winch. Read installation and operating instructions thoroughly.
• Always remove jewelry and wear eye protection. • Never lean over battery while making connections. • Never route electrical cables: o Across any sharp edges.
o Through or near moving parts. o Near parts that become hot.
• Always insulate and protect all exposed wiring and electrical terminals. • Always install terminal boots as directed in installation instructions. • Always use appropriate and adequate care in lifting components into place. • Always insure components will remain secure during installation and operation. • Always tighten all nuts and bolts securely, per the installation instructions.
• Always replace all worn or damaged parts before operating. • Never operate this WARN product with damaged or missing parts.
Read installation and operating instructions thoroughly.
1
TABLE OF CONTENTS
SECTION 4 - MAINTENANCE Section
SECTION 1 - GETTING STARTED Section
Description
Page
Description
Page
4.1
General Winch Maintenance
46 47
1.1 Identification 1.2 Definitions 1.3 Winch Operation
3 3 4
4.2 Winch Rope Maintenance
SECTION 5 - SERVICE KITS AND DIAGRAMS Section Description
SECTION 2 - DISASSEMBLY & ASSEMBLY Section Description
Page
5.1 Replacement Parts List 5.2 Replacement Parts Diagram
48-49
Page
50
2.1 Suggested Tools 2.2 Winch Disassembly 2.3 Winch Reassembly 2.4 Motor Disassembly
4
5-6 7-8
9-12
2.5 Motor Reassembly 2.6 Geartrain Dissembly 2.7 Geartrain Reassembly 2.8 Control Pack Disassembly 2.9 Control Pack Reassembly
13-16 17-22 23-30 31-34 35-37 38-39 40-41 42-43
2.10 Brake Disassembly 2.11 Brake Reassembly 2.12 Geartrain Clocking
SECTION 3 - TROUBLESHOOTING Section
Description
Page
3.1 Power In/Out
44 44 45 45
3.2 Brake 3.3 Clutch 3.4 Noise
2
This manual is intended for use by a WARN authorized service technician. It is important to make repairs with the proper tools and equipment. WARNING Read all instructions and safety information provided. Failure to do so, may cause the winch to fail, leading to personal injury. For full winch operation and techniques, as well as other product specific literature, visit www.warn.com. BEFORE YOU BEGIN
This manual covers the: • EVO Winch 8, 10, 12
SECTION 1 - GETTING STARTED
Winch serial number: The serial number is stamped on the drum support.
1.2 Definitions 1.2.1 Definitions Operation and service of a Warn planetary winch can be explained easier by defining a few major structural components. Refer to Figure 1.2 for the following definitions: MOTOR : The electric winch is driven by a high speed, low torque electric motor. A 12-volt DC vehicle battery generally powers the electric motor. REMOTE SOCKET : The remote socket is where the operator plugs in the wired remote control in order to control the winch. WINCH ROPE : The winch rope’s diameter and length are determined by the winch’s load capacity and design. Wrapped around the winch drum and fed through the fairlead, the winch rope is looped at the end to accept the hook’s clevis pin. Synthetic winch rope is constructed of a unique ultra high molecular weight polyethylene material and offers tremendous tensile strength. It is coated with a high temperature urethane and equipped with a temperature resistant sleeve on the first layer for added protection. The synthetic rope’s high flexibility and low weight make it much easier to handle out in the field. WINCH DRUM : The winch drum is the cylinder onto which the winch rope feeds. The drum is driven by the motor and drive train. Its direction can be changed using the remote control. DRUM SUPPORTS : Drum supports are the structural components of the winch that mount the winch to the vehicle. The drum rotates while being held by the drum supports and both the motor and gear train are attached to a drum support. GEAR TRAIN : Warn electric planetary winches consist of a gear train made up of three planetary gear stages. The purpose of the gear train is to multiply motor torque and to reduce motor speed transmitted to the drum. Warn gear trains are enclosed in a housing and are lubricated with grease. CLUTCH LEVER: The clutch lever allows the operator to manually disengage and engage the winch drum from the geartrain. Disengaging the clutch enables the drum to rotate freely (known as “freespooling”). Engaging the clutch “locks” the winch drum back onto the gear train. CONTROL PACK: Using electrical power from the vehicle’s battery, the control pack’s contactor switches power to the motor, enabling the operator to change the direction of the winch drum rotation.
1.1 Identification To ensure proper winch repair, it is necessary to correctly identify the model and part number of your winch. This makes ordering replacement parts easier and helps you obtain the necessary information from WARN customer service at 1-800-543-9276. NOTE: For a part description, item number and quantity, refer to the Replacement Parts List for your specific winch model at www.warn.com.
EVO
Control Pack
Motor
Remote Socket
Clutch Lever
Winch Drum
Remote Control
Transmission (Gear Train)
3
SECTION 2 - DISASSEMBLY AND ASSEMBLY
1.3 Winch Operation A Warn winch is a compact device used to pull heavy loads over short distances. The vehicle battery and charging system generates the power for pulling the load. Power feeds from the battery power source into the winch control pack. At the push of a remote control switch the power flows to the winch motor. The winch motor turns the electrical energy into mechanical energy. The motor shaft turns the motor coupler, which, in turn, drives the brake. On power-in operation, the brake simply rotates and drives the planetary gears, starting with the gear carrier stage farthest from the winch drum (the first stage carrier.) The first stage carrier, in turn, drives the second stage carrier, which then drives the third stage carrier. The third stage directly drives the drum. Since the winch rope is connected to the drum, the rope winds around the drum, causing the load to be drawn in. On power-out operation, the motor is reversed and the winch drum is rotated in the opposite direction. All winch components operate in the same manner as during power in except the brake. During power- out, the load tries to “over speed” the motor (make the motor turn faster than it would under its own power.) When the brake detects this over speed it engages just enough to make the load and motor run at the same speed and slow the load. When the remote control switch is released, the brake engages and completely stops the load.
NOTE: This service manual covers service steps for EVO Winches. Pay particular attention to the steps as some may or may not apply to your specific winch.
2.1 Suggested Tools The following tools are suggested for these procedures: • Metric Hex Key Wrench Set • Metric Box or Open End Wrenches • Flat Head Screwdriver • Pliers, including Long Nose Needle • Torque Wrench • Assortment of Torx Bits
4
2.2 Winch Disassembly
5
2. Separate tie plate, geartrain and motor assemblies.
Remove control pack / tie plate assembly. 1.
8-15 Nm (71-133 in. lbs.)
3.
4.
Remove control pack from tie plate.
Remove control pack motor cables and ground cable.
6
2.3 Winch Reassembly
7
1.
2.
Reinstall control pack to tie plate.
Connect control pack motor cables and ground cable.
7.5-11 N.m (66-97 in.lbs)
3.
4. Re-assemble control pack / tie plate assembly.
Re-assemble tie plate, geartrain and motor assemblies.
8-15 Nm (71-133 in. lbs.)
8
2.4 Motor Disassembly
9
Remove motor drum support assembly. 2.
1.
Remove motor armor.
Do NOT hold or place motor with shaft UP, the motor may disassemble
Remove motor from drum support. 4.
Remove motor bolts. 3.
Head: T30 M6 x 1mm x 160mm Torque: 10.6-13Nm (94-115inlb)
10
Remove motor seal from drum support. 5.
Rotate drum support. 6.
Remove nylon drum bushing from drum support. 7.
Remove motor drum seal from drum support. 8.
11
Remove brake retaining ring. 9.
Remove brake. 9.
4. Remove motor bearing.
12
2.5 Motor Reassembly
13
Flip motor drum support. 1.
2.
Press in motor bearing.
3.
Install retaining ring. 4.
Install brake.
14
Install motor drum seal to drum support. 5.
Press seal until fully seated
Verify seal does not sit above pocket wall
Rotate drum support. 7.
6. Install nylon drum bushing to drum support.
15
9.
Install motor seal to drum support. 8.
Head: T30 M6 x 1mm x 160mm Torque: 10.6-13Nm (94-115inlb) Install motor bolts. 11. 8-10 M.m (71-89 in.lbs)
Install motor to drum support. 10.
12. Install motor armor.
4-6 N.m (35-53 in. lbs)
16
2.6 Geartrain Disassembly
17
Remove geartrain (2.2 Winch Disassembly - steps 1 and 2). 1.
2.
Remove armor.
4.
3.
Remove geartrain bolts.
Remove geartrain drum support and clutch handle armor piece.
18
5. Remove O-ring (it may be stuck to either part).
6.
Remove 3rd stage ring gear.
Remove 3rd stage carrier, thrust washer, and 2nd stage carrier assemblies.
7.
8.
Remove 1st stage carrier and input gear.
19
9.
10.
Remove upper clutch handle.
Remove clutch handle plug and set screw.
12.
11.
Remove clutch handle stem.
Remove 2nd stage ring gear snap ring.
22mm
20
13.
14.
Remove 1st stage ring gear snap ring.
Remove 2nd stage ring gear.
16.
15.
Remove thrust washer.
Remove 1st stage ring gear.
21
17. Remove geartrain bearing.
22
2.7 Geartrain Reassembly
23
1.
2.
Install geartrain bearing.
Install 1st stage ring gear.
4.
3.
Install 1st stage ring gear snap ring.
Inspect stage snap ring to be sure it is fully seated.
24
6.
5.
Install 2nd stage ring gear snap ring.
Install 2nd stage ring gear.
Verify snap ring is seated and pushed into snap ring groove.
8.
Install clutch handle stem.
7.
Grease clutch handle stem threads.
22mm
Shell Gadus S5 V150XKD (light coat)
25
9. Install clutch handle plug and set screw.
10. TEMPORARILY install clutch handle
2.5-5N.m (20-89 in-lbs)
12. Install geartrain drum bushing and seal.
11. Verify turning the clutch handle engages and disengages the 2nd stage ring gear. * Once verified - remove clutch handle
2
2
1
1
26
13.
14.
Press in geartrain drum seal.
Press seal until fully seated
Verify seal does not sit above pocket wall
16. Install lower 3rd stage ring gear o-ring.
Flip drum support.
15.
27
17. Install 3rd stage ring gear. * Make sure the ring gear is aligned drum support gear train teeth.
18. Grease the 3rd stage ring gear, filling each tooth completely.
Shell Gadus S5 V150XKD (8.5-36g)
20.
Install the 3rd stage carrier. 19.
Grease 2nd stage sun gear, filling each tooth completely. Install the thrust washer and 2nd stage carrier.
1
Shell Gadus S5 V150XKD (1.5-10g)
2
28
21.
22.
Grease and install the 1st stage sun gear, filling each tooth completely.
Grease and install sun gear. 1 2
1
Shell Gadus S5 V150XKD (0.5-2g)
2
Shell Gadus S5 V150XKD (1.5-10g)
23.
24.
Combine geartrain drum support to end housing.
Install thrust washer.
4-7 N.m (35-62 in.lbs)
29
26.
25. Install clutch armor piece and clutch handle.
Install armor.
2.
4-6 N.m (35-53 in. lbs)
1.
2.5-3 N.m (20-27 in.lbs)
27.
28.
Grease the geartrain drum seal. Re-assemble winch (Section 2.3 Winch Reassemble steeps 3, 2, 1).
Install driveshaft. * Apply light pressure to the end cap while spinning the drive- shaft to seat into the end housing.
Shell Gadus S5 V220 2 (7-11g)
30
2.8 Control Pack Disassembly
31
Remove control pack from tie plate. 2.
Remove control pack assembly. 1.
Disconnect control pack cables. 3.
Remove control pack cover. 4.
32
Pull control pack cover away from base plate to expose internals. 5.
Disconnect harness from remote socket and set cover aside. 6.
Remove screw securing ground cables. 7.
Remove spade connectors. 8.
33
Remove contactor cables. 9.
Remove contactor. 10.
34
2.9 Control Pack Reassembly
35
1.
2.
Install the contactor.
Install contactor cables to coordinating colored contactor post.
Yellow
6-8 N.m (53-71 in-lbs)
1.5-2 N.m (14-22 in-lbs)
Blue
Red
Green
3.
4.
Install screw to secure ground cables.
Install spade connectors to coordinating contactor spade terminal color.
Blue
Black
Yellow
36
5.
6.
Close and reinstall the control pack cover, being sure to not pinch any wires.
Plug harness into remote socket.
7.
8.
9.
Connect control pack cables.
Install control pack to tie plate.
Install control pack assembly.
8-15 Nm (71-133 in. lbs.)
37
2.10 Brake Disassembly
38
Remove brake retaining ring. 1.
Remove brake. 2.
39
2.11 Brake Reassembly
40
1. Install brake.
2.
Install brake retaining ring.
41
2.12 Geartrain Clocking
42
1.
Remove armor. 2.
3.
Remove geartrain (Section 2.2, steps 1-2).
4.
Remove clutch handle and small armor plate.
Remove geartrain bolts.
1.
2.
5.
Reverse steps 3, 2, and 1
Turn geartrain support until bolt holes line up in desired clocking position. WARNING: DO NOT SEPARATE! THE O-RING SEAL MAY DISLODGE.
6.
7.
Install geartrain bolts.
4-7 N.m (35-62 in.lbs)
Glocking position examples
43
3.1.3
SECTION 3 – WINCH TROUBLE SHOOTING GENERAL WINCH TROUBLESHOOTING This section covers general troubleshooting. NOTICE You must use a 12VDC battery to perform any analysis on the EVO. Using any other type of power supply could result in an incorrect diagnosis. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION 3.1 Power In / Out 3.1.1
Too many layers of rope.
Pull capacity is reduced by approximately 14% per layer. Use winch on first layer of drum for maximum power. Rewind rope on drum so that it is level and not rubbing on other parts of winch. Ensure fairlead opening is properly sized for drum length Allow winch motor to cool for at least 10 minutes between short pulls. Increase cooling time for heavy loads or long pulls. See winch specification sheet. Reduce distance between winch and battery. Remove rope and replace with recommended rope dia. (3/8")
Rope is interfering with tie rod or other part of winch.
Reduced Pull Capacity
Motor is hot
Electrical wires too long Rope diameter too large
Clutch handle in freespool
Turn clutch handle to "Engaged"
Ground cable is not directly attached to battery. Control pack ground is not connected to the drum support Power or ground cables are damaged Loose or corroded connection on bat- tery or motor terminals. Vehicle charging system cannot keep up with winch
Attach ground cable to negative post of battery and/or clean battery post Connect or repair control pack ground wire as required
3.1.4
Excessive power supply capacity for winch Use standard 12V OEM power system equipment (alter- nator, battery, etc.) Incorrectly sized power cables used Any deviation from factory power cables will modify performance. Install Warn factory power cables.
Excess Pull Capacity
Route cables away from hot or moving surfaces. Re- place or repair power/ground cables as required
Clean and tighten all connections
Winch does not power IN or OUT
3.2 Brake 3.2.1
Stop and allow the battery to recharge
Rope is spooled onto the drum in the wrong direction.
Remove all rope and reinstall in the proper direction.
Worn motor brushes Replace motor Internal contactor components sticking Replace contactor Brake is binding
Load exceeds rating of winch
Refer to winch capacity on product label. DO NOT EXCEED LINE PULL RATING SHOWN ON PRODUCT LABEL.
Replace brake and drum
Excessive gear train wear, broken gear train components.
Disassemble gear train to investigate driveshaft, gear carriers, and ring gears. Replace if damaged or has excessive wear.
Winch will not hold load.
Brake is worn Replace brake assembly and drum Brake or brake coupler are damaged Replace brake assembly. Inspect brake couplers for damage or excess wear. Replace couplers if necessary. Power out distance is too long.
3.1.2 Winch
Allow winch to cool for at least 10 minutes between short pulls. Increase cooling time for heavy loads or long pulls.
Brake is not disengaging
Replace brake and drum
powers IN, but will not power OUT or powers out very slowly.
Load exceeds rating of winch and drum deformed
Refer to winch capacity on product label. DO NOT EX- CEED LINE PULL RATING SHOWN ON PRODUCT LABEL.
Internal contactor components sticking Replace contactor
44
3.3 Clutch 3.3.1 Winch will not shift to freespool or engaged
Rope is under tension. Excessive Housing Wear
Power out short distance to release line tension. Inspect clutch handle, clutch pin, and end housing. If excessive wear on clutch features, replace end housing and clutch assembly Disassemble gear train to investigate binding in drive- shaft, gear carriers, and ring gears. Replace if damaged or has excessive wear.
Damaged Gear Train
3.3.2 Winch is
Rope is stuck between lower layers on the drum Shift winch to freespool, connect rope to an anchor point, and slowly back up vehicle to free stuck layers of rope Rope stacked to one side of drum Avoid sharp angle pulls, make sure rope is wound level on drum Winch operation in cold environment. Shift winch to freespool and then power in for about 30 seconds without drum moving to redistribute geartrain grease.
difficult to freespool.
Winch has not been broken in. Incorrect mounting bolt pattern
Tension rope per Winch Quick Start instructions Inspect the mounting bolt pattern. If the winch is not mounted flat or the drum supports are not parallel, the geartrain may bind Power the winch in and out while watching the drum flanges. A drum with bent flange must be replaced.
Bent drum flange.
3.4 Noise 3.4.1 Winch makes rattle/ratchet
Brake is not broken in yet Drum bushing not lubricated.
Run winch normally. Brake pads will even out over time.
Grease drum bushings.
noise on power in.
45
• Keep winch free of dirt, oil, grease, water and other substances. Remove any overflow grease from bearings. • Check all mounting bolts and make sure they are tightened to proper torque. Replace any damaged fasteners. • Periodically check all hydraulic connections to be sure they are tight and free of corrosion. • Check rope for visible damage every time winch is operated. Examples of damage are: cuts, knots, mashed or frayed portions, and broken strands. Replace rope immediately if damaged. Failure to replace a damaged rope could result in breakage. • If winch drum continues to turn after controls are released, brake may need to be replaced. 4.1 General Winch Maintenance SECTION 4 - MAINTENANCE
Before first Operation
Check
After Each Use
Monthly
Semi-Annually
Yearly
Take time to fully read the Instructions and/or Operations Guide, and/or Basic Guide to Winching Techniques, in order to understand your winch and its operations
X
Check fasteners and make sure they are tight and to proper torque.
X
X
X
Replace damaged fasteners
X X X X X X X X X X X
X
X
X X X X X X X X X X X
X X X X X X X X X X X
Check electrical connections.
Verify wiring to all components is correct and be certain that all connections are tight Verify there is no exposed/bare wiring, terminals or cable insulation damage (chafing, cutting).
Repair or replace damaged electrical cable.
X
X
Visual Check of winch and electrical connections to ensure all components are free from corrosion:
Check Quick Connects and Contact Leads
Check Motor-Sub Assembly (Contactor, Motor/ Motor Terminals, OLI). Ensure Remote Socket and Remote control connections are not damaged
X
X
Check hydraulic connections
Visual check of winch and control valve
46
4.2 Winch Rope Maintenance Cleaning: • Use low pressure water to clean synthetic rope. Do not use any chemicals. • Do not direct high pressure water (pressure washers, car washes, etc.) directly between the drum support and drum flange or clutch lever. • Use low pressure water and a soapy rag or sponge to clean the winch. • Avoid using chemicals that may damage the finish. • Thoroughly clean salt residue from the winch as soon as possible to minimize corrosion. Rope Inspection: WARNING Always inspect winch rope, hook, and slings before operating winch. Frayed, kinked or damaged winch rope must be replaced immediately. Damaged components must be replaced before operation. Protect parts from damage. When rope is first used, the outer filaments of the rope will quickly fuzz up. This is the result of these filaments breaking and this roughened surface will actually protect the fibers underneath. The condition should stabilize, not progress. If the surface roughness increases, excessive abrasion is taking place and strength is being lost. Look closely at both the inner and outer fibers. When either is worn the rope is obviously weakened. Open the strands and look for powdered fiber—this is a sign of internal wear. Localized discolorations could potentially represent chemical attack by anything from gear oil to battery acid. When doubt exists, replace the rope. Maintenance: • Inspect the winch rope and heat sleeve before and after each winching operation. Frayed or damaged rope must be replaced immediately. See rope care and storage. • The rope must always spool onto the drum as indicated by the drum rotation decal on the winch. • Use winch cover to protect winch and synthetic rope when not in use. Prolonged exposure to ultraviolet rays from sunlight can degrade synthetic rope strength over time. • Avoid using synthetic rope over any rough surfaces without abrasion protection. • Keep winch rope free of moisture, grease, dirt or other debris. If necessary, clean with a damp cloth.
Rope should be replaced when: • Rope bulk anywhere along the length is reduced by 10% or more by abrasion. • Two or more adjacent strands are cut. • Flat areas or lumps are found that are not eliminated by flexing rope. • Excessive fused or melted fibers are found. Any such areas will be stiff and the rope will have a glazed appearance.
• Rope with original bulk.
• Rope displaying 25% strand volume reduction from abrasion—rope should be replaced.
• Rope strand showing full volume.
• Rope strand reduced by 25% abrasion—rope should be replaced.
• Rope exhibits fiber-set from compression. A slight sheen is visible. This is not a permanent characteristic and can be eliminated by flexing the rope.
• Rope displays two adjacent cut strands—rope should be replaced.
47
SECTION 5 - SERVICE PART/KIT LIST AND DIAGRAM
48
SECTION 5 - SERVICE PART/KIT LIST AND DIAGRAM
49
50
Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45 Page 46 Page 47 Page 48 Page 49 Page 50Powered by FlippingBook