POWER SOURCE
POWER SOURCE
The PullzAll is available in both corded and cordless models. Each model has its own bene fi ts. Ensure the power source is connected properly following these instructions: Corded 120 VAC PullzAll Properly Grounded Plug Ensure the PullzAll power cord is connected to a properly grounded, 3-prong electrical socket with a Ground Fault Circuit Interrupter (GFCI). Minimum Amperage If using an extension cord and/or generator, make sure that it is rated to handle a minimum of 15 Amps, the current required to run the PullzAll at full capacity. Cordless 24V DC PullzAll Battery Care Always turn On/Off power switch off when not in use. Permanent battery damage may occur if the unit is allowed to self- discharge in the ‘On’ position. Store battery and charger in locations where temperatures will not exceed 120ºF (49 ºC). When noticeable loss of performance is observed, replace battery pack with a fully charged battery. Avoid running the battery completely dead. This can cause permanent damage to the battery pack. Installing the Battery Pack 1) Verify the power switch is in the ‘Off’ position. 2) Slide the battery pack into the body, making sure that the latch is fully engaged. The battery release button must be in the top position. Removing the Battery Pack 1) Verify the power switch is in the ‘Off’ position. 2) Push down the battery release
button at the back of the battery and slide the battery away from the PullzAll body.
Charger Safety Rules
If the battery does not charge properly: a. Check for voltage at the outlet by plugging in some other elec- trical device. b. Verify charger voltage is ap- proximatly 30vdc. Refer to charger plug pinout here or on charger label.
Follow these important safety instructions and review the cautionary markings on the battery charger, battery pack, and the Cordless PullzAll tool before using the Cordless PullzAll battery charger. Remove charger from power source when battery is fully charged. Use only the charger that accompanies the Cordless PullzAll or an Of fi cial WARN charger accessory. Only charge WARN Cordless PullzAll rechargeable batteries, other types of batteries may burst causing personal injury and damage. Do not charge the battery in damp or wet environment. Do not disassemble the charger. Take it to a Warn authorized service center when service is required. Important Charging Notes 1) The battery pack accepts only about 80% of its maximum capacity with its fi rst few charge cycles. However, after the fi rst few charge cycles and normal usage, the battery will charge to full capacity. 2) The charger was designed to fast charge the battery, only when the battery temperature is between 32ºF (0º C) and 120ºF (49º C). If the battery pack is too hot or too cold, the battery pack should not be charged. (This may happen if the battery pack is hot from heavy use.) Wait until the battery returns to room temperature before charging. 3) A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced.
Charging the Battery Pack Plug charger’s power cord into a standard power outlet, then insert the battery charging plug from the charger into the battery. The charger’s red LED indicator light will be solid, indicating charging.
WARNING Always avoid contact with battery leakage, which may occur under extreme usage or temperature conditions. Never attempt to disassemble the battery or remove any component. Always let battery cool before using in tool and before charging. Never leave the PullzAll power cord plugged in or the battery in unit when installing, servicing or storing. WARNING NOTICE WARNING
c. Check battery pack terminals for dirt. Clean with a cotton swab and alcohol if necessary. d. If you still do not get proper charging, contact Warn cus- tomer service. The PullzAll battery uses NiMH technology. Check your local ordinances/regulations for disposal or recycling regulations. Prior to disposal, protect exposed terminal with heavy insulating tape to prevent shortage. Battery Disposal
A fully discharged battery should charge in approximately two hours. Charging will automatically stop when charging is complete. For best performance, unplug the charger and allow the battery to cool to room temperature before use in the PullzAll. The battery charger indicator light signi fi es: 1) Green LED on: Fully charged 2) Red LED on: Charging 3) Red LED fl ashing: A fault condition is present. 4) Green LED fl ashing: Over temperature protection.
Chemical First Aid : If leakage from battery comes in contact with skin, wash with soap and water. If liquid gets into eyes, fl ush with water for 15 minutes.
If the red LED is fl ashing, stop charging the battery and follow the charger safety rules below. If the problem persists, contact a Warn authorized service center.
WARN INDUSTRIES * THE BASIC GUIDE TO UTILITY PULLING 13
WARN INDUSTRIES * THE BASIC GUIDE TO UTILITY PULLING 14
Powered by FlippingBook